|
|
It is currently Sat May 04, 2024 4:07 pm
|
|
Page 1 of 1
|
[ 8 posts ] |
|
Explorer/Cobra Upper intake & Serp, 302 Roller shortblock
| Author |
Message |
|
landshark
Official CCB Member
Joined: Fri Oct 14, 2011 12:16 am
Posts: 3942
Location: Denver, Wash Park Area
|
 Explorer/Cobra Upper intake & Serp, 302 Roller shortblock Looking at picking up a 302 roller block from a mustang or even a Fullsize F150 - Bronco (94-96)
Also looking for the explorer serp setup and upper intake, MAF and all the goodies off the top end.
Ideally would love to pick up a pair of GT40 heads as well.
I will be getting the heads rebuilt and the block looked over, possibly cleaned and honed.. depending on condition and mileage.
The pick n pull in denver is a bit short on explorer parts, but i know other yards in the greater denver area are a bit easier to find stuff in.
Any leads will help - thanks guys!
_________________
1976 Bronco "Green, Yellow, whatever", 1969 Bronco "Red", 1972 Bronco Stocker "Kind of Blue/Grayish"
|
| Fri Jun 01, 2012 9:57 am |
|
|
|
crawlercreations
Official CCB Member
Joined: Sat Nov 06, 2010 9:36 pm
Posts: 1101
Location: Arvada
|
Re: Explorer/Cobra Upper intake & Serp, 302 Roller shortbloc Call this guy I have purchased a lot of parts from, Ed 303-936-4021. Sold my Co worker a complete ready to run with less than 100k miles roller 351w for $275. Constantly has engines in various condition laying around and always cheap! Knows his stuff about fords too!
_________________
There is a fine line between "hobby" and "mental illness"
|
| Fri Jun 01, 2012 10:37 am |
|
|
|
Rox Crusher
Official CCB Member
Joined: Sun Oct 10, 2010 5:36 pm
Posts: 3980
Location: Roxborough Park, Colorado
|
Re: Explorer/Cobra Upper intake & Serp, 302 Roller shortbloc not much of a help but I have a spare clutch fan with steel blades off of Explorer 5.0 if you would like it
_________________
1977 Sport, 351w OBDII EFI motor, 4R70W auto, 4:88 gears, ARB lockers, 3.5" suspension, 33" tires.
|
| Fri Jun 01, 2012 10:48 am |
|
|
|
landshark
Official CCB Member
Joined: Fri Oct 14, 2011 12:16 am
Posts: 3942
Location: Denver, Wash Park Area
|
Re: Explorer/Cobra Upper intake & Serp, 302 Roller shortbloc
_________________
1976 Bronco "Green, Yellow, whatever", 1969 Bronco "Red", 1972 Bronco Stocker "Kind of Blue/Grayish"
|
| Fri Jun 01, 2012 10:50 am |
|
|
|
akaFrankCastle
Official CCB Member
Joined: Wed Oct 27, 2010 6:25 pm
Posts: 4901
Images: 0
Location: Colorado Springs
|
Re: Explorer/Cobra Upper intake & Serp, 302 Roller shortbloc Last I was at the COS yard all the GT40s were stripped. A few GT40P motors still laying around though. I'll keep my eyes open.
_________________
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
|
| Sat Jun 02, 2012 7:44 pm |
|
|
|
landshark
Official CCB Member
Joined: Fri Oct 14, 2011 12:16 am
Posts: 3942
Location: Denver, Wash Park Area
|
Explorer/Cobra Upper intake & Serp, 302 Roller shortblock Went today pulled gt40 heads explorer upper and part of the serp before the rain moves in. Pulled everything off a 97 mountaineer
_________________
1976 Bronco "Green, Yellow, whatever", 1969 Bronco "Red", 1972 Bronco Stocker "Kind of Blue/Grayish"
|
| Sat Jun 02, 2012 10:00 pm |
|
|
|
landshark
Official CCB Member
Joined: Fri Oct 14, 2011 12:16 am
Posts: 3942
Location: Denver, Wash Park Area
|
Re: Explorer/Cobra Upper intake & Serp, 302 Roller shortbloc ok didn't get all the parts i needed.. and was having a bear of a time trying to get the clutch fan and balancer off.. any tricks to getting them off in the yard? the balancer has that bolt then you can use a puller to yank it off or if your lucky it might pull off correct? I guess i can take a crobar and try to stop the motor from turning? Was getting frustrated so stopped trying to get it off.. anyway got this stuff.. Iam going to reuse my 78 block but taking it in to get looked at and refreshed a bit. 
_________________
1976 Bronco "Green, Yellow, whatever", 1969 Bronco "Red", 1972 Bronco Stocker "Kind of Blue/Grayish"
|
| Mon Jun 04, 2012 9:27 pm |
|
|
|
landshark
Official CCB Member
Joined: Fri Oct 14, 2011 12:16 am
Posts: 3942
Location: Denver, Wash Park Area
|
Explorer/Cobra Upper intake & Serp, 302 Roller shortblock Ok got everything I need. Thanks guys
_________________
1976 Bronco "Green, Yellow, whatever", 1969 Bronco "Red", 1972 Bronco Stocker "Kind of Blue/Grayish"
|
| Thu Jun 21, 2012 9:44 pm |
|
|
|
|
|
Page 1 of 1
|
[ 8 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 2 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
