|
It is currently Fri Nov 15, 2024 9:23 am |
|
All times are UTC - 7 hours [ DST ] |
|
Page 1 of 1 |
[ 4 posts ] |
| Previous topic | Next topic |
Dana 44 spindle problem
| Author | Message |
|---|---|
|
Official CCB Member   Joined: Fri Oct 14, 2011 12:16 am Posts: 3942 Location: Denver, Wash Park Area 
|
 Dana 44 spindle problemI posted this over at cb.com but thought i coudl get some insight here as well...
I'm in the middle of rebuilding my stock 76 dana44 axle and noticed a difference between the spindles. One has a machined groove on the inside the other does not.. when i removed the hub the passenger side bearing was toast and stuck on the spindle pretty good. As far as I know this is an original dana 44 and nothing up front has ever been replaced however I assume both spindles should be the same, however they are not.. and would explain why the bearing was seized onto the spindle.. anyway I need to know if this is stock and if not which spindle is the correct one? Why are they different? The one on the right has a groove on the inside, the other is flat.. the left one does not have any groove thats a mark left from the thrust washer off the stub axle...  here is a bit better photo of the grooved one...  maybe i should just replace both spindles... the one with the stuck bearing is showing quite a bit of color change from the temp..  any ideas? was about to put in the new bearings and seals but holding off until i can figure this out.. _________________ 1976 Bronco "Green, Yellow, whatever", 1969 Bronco "Red", 1972 Bronco Stocker "Kind of Blue/Grayish" |
| Sat Dec 17, 2011 10:33 pm |
|
|
|
|
Moderator   Joined: Mon Nov 15, 2010 5:58 pm Posts: 3906 Location: Henderson, Co
|
Re: Dana 44 spindle problem edit im having a brainfart....
_________________ Rob 74 Ranger EFI351w, 4r70w, ARB 5.13 9in, ARB 5.13D44, and a bunch of other goodies. Best of all the family memories. 04 Mustang Cobra, KenneBell 2.2 feeding a lot of boost on E85. Tire shredding machine New project: 77 Bronco Ranger, body work and more body work. Very little left of a 72 durango tan explorer sport |
| Sat Dec 17, 2011 10:53 pm |
|
|
|
|
|
Re: Dana 44 spindle problem Look at these early D44 spindles. viewtopic.php?f=9&t=1424&hilit=spindle
|
| Sun Dec 18, 2011 12:13 am |
|
|
|
|
Official CCB Member Joined: Fri Oct 14, 2011 12:16 am Posts: 3942 Location: Denver, Wash Park Area
|
Re: Dana 44 spindle problem so the correct spindle is the one without the machined groove... somone must have swapped one in or someone screwed up at the factory... iam going with the factory... it was the 70's afterall...
I assume that I can hit up the junkyard and pull a 78-79 bronco or f150 spindle or see if anyone here as one laying around for a 76-79? _________________ 1976 Bronco "Green, Yellow, whatever", 1969 Bronco "Red", 1972 Bronco Stocker "Kind of Blue/Grayish" |
| Sun Dec 18, 2011 12:21 am |
|
|
|
|
|
Page 1 of 1 |
[ 4 posts ] |
|
All times are UTC - 7 hours [ DST ] |
Who is online |
Users browsing this forum: No registered users and 3 guests |
| You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum |