|
|
Register •
FAQ
• Login
|
|
|
It is currently Sat Nov 02, 2024 11:25 am
|
|
Page 1 of 1
|
[ 2 posts ] |
|
| Author |
Message |
|
landshark
Official CCB Member
Joined: Fri Oct 14, 2011 12:16 am
Posts: 3942
Location: Denver, Wash Park Area
|
 Engine first start I might be jumping ahead of myself a little, however I will be picking up one more order of parts this week/weekend and pending any show stoppers would be in a position to fire up the engine this weekend or even this week. I have a small checklist for engine start but wanted to make sure I have everything I need to start and pick up anything i would be missing.
Details of the engine for those that forgot or care:
Non roller block, with a used flat tappet cam and new lifters. Crank has been polished, new crank bearings. Cylinder walls have been bored out, new rings used pistons. Heads have been redone.
Obvious first:
Engine oil with Zinc additive (5 or 6 Quarts) regular 5w-30? non synthetic?
Transmission oil - Regular ATF? Torque Convertor already has 1 or 2 quarts in it.. so i would need about 5 more correct?
Transfer Case oil - ATF? 2 quarts?
Front and rear Diff oil 1.9 in front about 3 in rear
Antifreeze a bunch of gallons.
Before start prime engine someone was saying using a 1/4 socket on the end of an extension as long as the socket is attached to the end of the extension REALLY well.. i also have an extra distributor but would have to get the gear off of it before i used it to prime i assume.. .
Once its primed do i need to turn the engine over anymore? I know i have to make sure its at Top Dead Center.. but not sure i really need to turn the engine over at this point.
Once i get it running I was told even though the cam is used I should break in the cam to lifters.. so run it about 20 -30 min at about 2000 RPMS. Is this true?
If so and I have problems on first start and for whatever reason can't keep it running will it hurt the engine to start it a few times before I can run it for the 20-30 min?
I know it will be loud but I might not have any way to hook up a full exhuast at first. Will it hurt anything to run open headers? I MIGHT be able to get the o2 sensors in some short pipes but dont know yet.. i know its not ideal to run it without them but i can hook them up and figure something out?
Anything else i should look for or know before I start it up?
_________________
1976 Bronco "Green, Yellow, whatever", 1969 Bronco "Red", 1972 Bronco Stocker "Kind of Blue/Grayish"
|
| Wed Sep 05, 2012 2:28 pm |
|
|
|
akaFrankCastle
Official CCB Member
Joined: Wed Oct 27, 2010 6:25 pm
Posts: 4901
Images: 0
Location: Colorado Springs
|
Re: Engine first start
_________________
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
|
| Wed Sep 05, 2012 10:21 pm |
|
|
|
|
|
Page 1 of 1
|
[ 2 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 4 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
