|
|
It is currently Sat Nov 02, 2024 1:38 pm
|
|
Page 1 of 1
|
[ 6 posts ] |
|
| Author |
Message |
|
cwin74
Official CCB Member
Joined: Tue Apr 17, 2012 7:37 am
Posts: 139
Images: 0
Location: Broomfield - Colorado
|
 4H won't engage I'm not able to shift into 4H, but 4L seems to work just fine. I recently added a 2" body lift could this be the culprit? My current thought is the shifter can't go back far enough to engage 4H. What should I look at first?
I hope to get this corrected before Sunday!
|
| Thu Sep 13, 2012 7:40 am |
|
|
|
akaFrankCastle
Official CCB Member
Joined: Wed Oct 27, 2010 6:25 pm
Posts: 4901
Images: 0
Location: Colorado Springs
|
Re: 4H won't engage A 2" BL could have moved the body panels up enough to interfere with your shift pattern. First thing I would do is pull up your shifter boot from the floor, pull the shifter back to the 4H position, and see if the shifter is making contact on the back side of that opening. If it is, you might need to do a little trimming to get the full throw.
_________________
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
|
| Thu Sep 13, 2012 8:21 am |
|
|
|
cwin74
Official CCB Member
Joined: Tue Apr 17, 2012 7:37 am
Posts: 139
Images: 0
Location: Broomfield - Colorado
|
Re: 4H won't engage A very good idea, that is exactly what I will be doing after work today. Thanks man.
|
| Thu Sep 13, 2012 1:00 pm |
|
|
|
akaFrankCastle
Official CCB Member
Joined: Wed Oct 27, 2010 6:25 pm
Posts: 4901
Images: 0
Location: Colorado Springs
|
Re: 4H won't engage No worries. I'm thinking that if you aren't interested in doing any cutting, you might be able to pull your shifter out, heat it up, and bend it a little to clear that spot. Not a huge fan of BLs (nothing against your choice), so I haven't run in to this issue yet.
_________________
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
|
| Thu Sep 13, 2012 1:02 pm |
|
|
|
cwin74
Official CCB Member
Joined: Tue Apr 17, 2012 7:37 am
Posts: 139
Images: 0
Location: Broomfield - Colorado
|
Re: 4H won't engage I'm also not a huge fan of body lifts. The body lift was a quick fix to fit the EFI intake under the stock hood. I wanted to keep the stock hood and need to be able to close the hood. Plus I can fit some 35's under the Bronco with less worry. =)
Thanks again for the advice!
|
| Thu Sep 13, 2012 1:40 pm |
|
|
|
cwin74
Official CCB Member
Joined: Tue Apr 17, 2012 7:37 am
Posts: 139
Images: 0
Location: Broomfield - Colorado
|
Re: 4H won't engage I removed the boot and the shifter is resting on the frame where it needs to go back into 4H. I'm either going to need to cut a notch or bend the shifter. I'm cool with easy fixes.
|
| Fri Sep 14, 2012 6:47 am |
|
|
|
|
|
Page 1 of 1
|
[ 6 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 2 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
