|
It is currently Sat Nov 23, 2024 8:18 am |
|
All times are UTC - 7 hours [ DST ] |
|
Page 1 of 1 |
[ 6 posts ] |
| Previous topic | Next topic |
Timing Chain
| Author | Message |
|---|---|
|
Official CCB Member   Joined: Mon Feb 14, 2011 10:29 am Posts: 768 Location: The MHC 
|
 Timing ChainSo...I got started doing my Explorer EFI conversion Saturday by disassembling my motor down to basically the small block. I noticed the timing chain may have excessive slack in it. I turned the motor to #1 TDC and with the chain tight on the driver side, I have approximately 3/4" of play on the opposite side. This motor only has about 40-50K on it. Time for replacement? If so, what to buy? I at least know I don't need to install the fuel pump eccentric if replaced.
Thoughts? _________________ Wilma - 71 1/2 Wagon; 3 1/2" WH lift, 1" BL, NP435, Chebby disc front, WH twin stick D20, EFI 302, Cool hood scoop, mucho cancer; purchased in 1990. |
| Mon Feb 02, 2015 10:03 am |
|
|
|
|
Official CCB Member  Joined: Thu Oct 25, 2012 9:33 pm Posts: 2460
|
Re: Timing Chain I just bought this one (http://www.jegs.com/i/COMP+Cams/249/2138/10002/-1) to replace mine. Also-- so you don't make the same mistake I did-- when eliminating the fuel pump eccentric-- make sure you still attach the bolt and washer to the gear and cam.
_________________ 69 Wagon, 351W, Explorer EFI & Serpentine, ZF5, 35" tires, 3.5 SL, 2 BL, WARN 8274 |
| Mon Feb 02, 2015 11:04 am |
|
|
|
|
Official CCB Member  Joined: Tue May 07, 2013 10:37 pm Posts: 1485
|
Re: Timing Chain 3/4" sounds like it's at it's useful limit. Timing chains are cheap.
|
| Mon Feb 02, 2015 2:47 pm |
|
|
|
|
Official CCB Member  Joined: Wed Oct 27, 2010 6:25 pm Posts: 4901 Images: 0 Location: Colorado Springs
|
Re: Timing Chain X2. It's open already. Might as well get another 100k out of the motor by replacing it.
_________________ Stroppe'd 1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar. The Terrible One 1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering. 1973 Stroppe Baja project |
| Mon Feb 02, 2015 5:20 pm |
|
|
|
|
Official CCB Member Joined: Mon Feb 14, 2011 10:29 am Posts: 768 Location: The MHC
|
Re: Timing Chain Measured again last night and I'm at or near the 1/2" play required for replacement. So which do I get? Double roller? True Roller? Something cheap? Billet sprockets? I've never bought one before. I'm surprised (but really not) that this chain only lasted 40-50K. I want to install something that's going to last at least 80K miles!
_________________ Wilma - 71 1/2 Wagon; 3 1/2" WH lift, 1" BL, NP435, Chebby disc front, WH twin stick D20, EFI 302, Cool hood scoop, mucho cancer; purchased in 1990. |
| Tue Feb 03, 2015 9:02 am |
|
|
|
|
Official CCB Member  Joined: Wed Sep 29, 2010 10:03 pm Posts: 4371 Images: 0 Location: Parker, CO
|
Re: Timing Chain It's the chain that wears, so a double roller would likely last longer. Not sure what benefit billet sprockets would add, bling maybe.
_________________ Best to Date MPG: 26.6 |
| Tue Feb 03, 2015 10:03 am |
|
|
|
|
|
Page 1 of 1 |
[ 6 posts ] |
|
All times are UTC - 7 hours [ DST ] |
Who is online |
Users browsing this forum: No registered users and 6 guests |
| You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum |