|
It is currently Thu Nov 21, 2024 7:31 pm |
|
All times are UTC - 7 hours [ DST ] |
|
Page 1 of 1 |
[ 7 posts ] |
| Previous topic | Next topic |
9" pinion yoke pre load setting?
| Author | Message |
|---|---|
|
Official CCB Member   Joined: Fri Nov 19, 2010 11:16 pm Posts: 587 Location: Lakewood/Green Mtn. 
|
 9" pinion yoke pre load setting?I need to swap the pinion yoke on the rear diff. The more I look into it the more questions I have. How do you determine the preload on the old yoke and make sure the new one is set properly? is it a matter of torqe or pinion drag or what ? Do I need to pull the center section to do it or just pull the nut and put the new one on ?
Any tips would be helpfull. Thanks. |
| Thu Jul 07, 2011 4:49 pm |
|
|
|
|
Official CCB Member Joined: Fri Nov 19, 2010 11:16 pm Posts: 587 Location: Lakewood/Green Mtn.
|
Re: 9" pinion yoke pre load setting? Thats more like it, nice and easy. Thanks
|
| Thu Jul 07, 2011 5:08 pm |
|
|
|
|
Official CCB Member  Joined: Sat Nov 13, 2010 12:31 am Posts: 516 Images: 1 Location: littleton
|
Re: 9" pinion yoke pre load setting? I go just a hair passed your mark just to make sure there is still tension in the crush sleeve.
|
| Thu Jul 07, 2011 6:31 pm |
|
|
|
|
Official CCB Member  Joined: Thu Nov 11, 2010 10:36 am Posts: 5984 Location: California
|
Re: 9" pinion yoke pre load setting? Or replace the crush sleeve.
_________________ 1973 Bronco, 351 SEFI, Locked, discs, 35's ZF-5spd and Atlas 4spd. 235:1 Crawl Ratio. It may be ugly, but it's slow. http://www.ucora.org |
| Fri Jul 08, 2011 8:56 am |
|
|
|
|
Official CCB Member Joined: Thu Nov 11, 2010 10:36 am Posts: 5984 Location: California
|
Re: 9" pinion yoke pre load setting? _________________ 1973 Bronco, 351 SEFI, Locked, discs, 35's ZF-5spd and Atlas 4spd. 235:1 Crawl Ratio. It may be ugly, but it's slow. http://www.ucora.org |
| Fri Jul 08, 2011 11:12 am |
|
|
|
|
Official CCB Member Joined: Fri Nov 19, 2010 11:16 pm Posts: 587 Location: Lakewood/Green Mtn.
|
Re: 9" pinion yoke pre load setting? Ok so, I either went half a turn to far or half a turn to short? It seems to be real tight (the nut) I put my torqe wrench on it just to see about how tight it was and its about 120 ftlb now, is there a typical torqe rang? Should I leave it or go the half turn more ?
|
| Sat Jul 09, 2011 2:01 pm |
|
|
|
|
Official CCB Member  Joined: Sat Nov 06, 2010 9:36 pm Posts: 1101 Location: Arvada
|
Re: 9" pinion yoke pre load setting? 150-175 is pretty good. As long as your rotational torque is within spec.
_________________ There is a fine line between "hobby" and "mental illness" |
| Sat Jul 09, 2011 5:04 pm |
|
|
|
|
|
Page 1 of 1 |
[ 7 posts ] |
|
All times are UTC - 7 hours [ DST ] |
Who is online |
Users browsing this forum: No registered users and 8 guests |
| You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum |