What have you done to your Bronco today? (v.2)

[tod]

The GT40 lower is about .46" taller than the truck lower and BCBroncos adapter combined.

[Gunnibronco]

Interesting. You don't happen to have an extra, or a line on others? I know its a dumb question, but I have to ask.

[tod]

No. I spent a long time looking for this one.

If anyone needs the BCBroncos setup, I would make them a heck of a deal though.

Interesting. You don't happen to have an extra, or a line on others? I know its a dumb question, but I have to ask.

[airbur]

Replaced the connector for the temp sending unit. Replaced a fuse in my ohm meter. Looked at the disassembled tranny on my bench. Exciting stuff.

[airbur]

Been working on the Toy Tug to get it ready for the season. I got all 4 Frame Mounted Tork Lifts installed, that was a Biotch and installed the 5th wheel plug in the box. Cutting that 2" hole in a new truck was painfull but I'm glad it is done and its all ready to go.

Sweet! Now, say that again in English:)

[airbur]

I removed the Corbeau 4 point harnesses and installed the regular 3 point retractables from WH. What a difference! These actually work great. The use the stock seat belt holes on the floor and you only need to drill one 1/2" hole about 35" up on each side of the cage. The buckle comes in a hard-plastic sleeve that you can bend and puts the connector right in the corner of each seat.

[kchaser]

Put on my new Autolite 2bbl. Sad day when you remove a worked 670 Holley and put on a 2bbl just so you can go up a hill. It lost a little snot but not bad.

[Booger]

Got to run out some winch cable to re-spool it while pulling Steve's Bronco into Zoso's garage. Now I need a new roller fairlead. And then need to run a remote winch controls into the cab so I don't have to drag out the winch controller all the time.

[crawlercreations]

Finished up the wiring and mounted my front clip permanently finally and got my dash mocked up and painted. Getting closer!

[Rox Crusher]

looking great !

[hockeydad4-22]

Finished up the wiring and mounted my front clip permanently finally and got my dash mocked up and painted. Getting closer!

Let me tell ya, I am seriously diggin the tube front end. That is awesome.

[Moab Mike]

Bought a complete operational Hickey Sidewinder III 9K lb. Winch with the original manual for $300.

[Rox Crusher]

Bought a complete operational Hickey Sidewinder III 9K lb. Winch with the original manual for $300.

hey, let's not BS folks.................

he bought a complete operational Hickey Sidewinder III in pristine condition

count me jealous !

[Moab Mike]

I call!

[Moab Mike]

More

[Viperwolf1]

Nice. What did it come out of, cause it wasn't a Bronco?

[Moab Mike]

Nice. What did it come out of, cause it wasn't a Bronco?

1976 Jeep Cherokee

[Viperwolf1]

You'll have to take a look at mine this weekend and see how the support structure is built.

[Moab Mike]

You'll have to take a look at mine this weekend and see how the support structure is built.

See you at Jeff's!

[airbur]

Stopped by RaptorRacer's today....he and his dad are installing the full Tom's Bronco Parts power steering conversion.

[airbur]

You'll have to take a look at mine this weekend and see how the support structure is built.

See you at Jeff's!

What? A secret bronco meeting at Jeff's???

[Rox Crusher]

You'll have to take a look at mine this weekend and see how the support structure is built.

See you at Jeff's!

What? A secret bronco meeting at Jeff's???

Come on over anytime today or tomorrow

We are tearing tranny down today

[crawlercreations]

I finally got my cage tied into the frame today! Took way longer than I wanted but it came out pretty good. 1.5" o.d. .25 wall tubing should be sufficient!! Cage is now tied into the frame from the very front to the very rear.

[Viperwolf1]

What? A secret bronco meeting at Jeff's???

Come on over anytime today or tomorrow

We are tearing tranny down today

Mission accomplished.

Bronco 022.jpg

I hope Jeff kept track of how it goes together because I have no idea.

[landshark]

Got my 9' back together yesterday finally... hoping to get the brakes put back on and all the lines then roll it out of the way and start back up on the body/frame touch up cleaning. hoping to start painting the frame this afternoon! - ohhh optimism is great!

[Gregg]

I picked up some old (1970's --"Arkay" ?) box speakers for $2. Anyhow, they kick a$$ and they fit my budget.

[hockeydad4-22]

Lets see, we installed the throttle kick down, replaced the brights switch so now we have head
Lights, hung and adjusted the doors, installed a new windshield, cleaned all the glass, glued some of the lose weather seals in place.....

And drove it. seems to be burning rich, will need to adjust the carb.

Then we cleaned the garage. For the first time since october, hockey mom gets to park her car in the garage

[D&D72]

Just in time for winter!

[Rox Crusher]

Then we cleaned the garage. For the first time since october, hockey mom gets to park her car in the garage

We have some truly understanding wives............

[hockeydad4-22]

Then we cleaned the garage. For the first time since october, hockey mom gets to park her car in the garage

We have some truly understanding wives............

Not so much an understanding wife, but the boys have a very understanding mother, that is for sure!