|
It is currently Fri Nov 01, 2024 2:40 pm |
|
All times are UTC - 7 hours [ DST ] |
|
Page 1 of 1 |
[ 9 posts ] |
| Previous topic | Next topic |
4 degree steel shims
| Author | Message |
|---|---|
|
Official CCB Member   Joined: Fri Oct 14, 2011 12:16 am Posts: 3942 Location: Denver, Wash Park Area 
|
 4 degree steel shimslooking for 4 degree steel shims for the rear leafs, thanks
_________________ 1976 Bronco "Green, Yellow, whatever", 1969 Bronco "Red", 1972 Bronco Stocker "Kind of Blue/Grayish" |
| Fri May 31, 2013 4:25 pm |
|
|
|
|
Official CCB Member  Joined: Tue Jan 25, 2011 9:33 am Posts: 207 Location: Aurora, CO
|
Re: 4 degree steel shims I have zinc 4 degree shims in stock here. Steel are pretty hard to find.
_________________ You will not see me cry because I do not sing the blues |
| Fri May 31, 2013 4:48 pm |
|
|
|
|
Official CCB Member  Joined: Mon Jan 03, 2011 6:07 pm Posts: 4074 Location: Gardnerville, NV
|
Re: 4 degree steel shims _________________ "America is at that awkward stage. It's too late to work within the system, but too early to shoot the bastards." – Claire Wolfe 74-AWB 98", ZF5, Atlas4, TGW HP1060 and HP1014 axles, ARBs, 37's, 3.5" lift-5.5" front coil springs, Tahoe rear springs, EFI 302, h-boost, York OBA, 4x4x2, custom dash & gauges 72 U15- Explorer Sport-Candyapple Red (1 of 141) |
| Fri May 31, 2013 5:19 pm |
|
|
|
|
Official CCB Member Joined: Fri Oct 14, 2011 12:16 am Posts: 3942 Location: Denver, Wash Park Area
|
Re: 4 degree steel shims What does zinc do for me? Sounds risqué
_________________ 1976 Bronco "Green, Yellow, whatever", 1969 Bronco "Red", 1972 Bronco Stocker "Kind of Blue/Grayish" |
| Fri May 31, 2013 9:16 pm |
|
|
|
|
Official CCB Member  Joined: Thu Nov 11, 2010 10:36 am Posts: 5984 Location: California
|
Re: 4 degree steel shims Corrosion resistance. Are they solid zinc or just coated with zinc?
_________________ 1973 Bronco, 351 SEFI, Locked, discs, 35's ZF-5spd and Atlas 4spd. 235:1 Crawl Ratio. It may be ugly, but it's slow. http://www.ucora.org |
| Tue Jun 04, 2013 3:19 am |
|
|
|
|
Official CCB Member Joined: Tue Jan 25, 2011 9:33 am Posts: 207 Location: Aurora, CO
|
Re: 4 degree steel shims They are solid zinc. Zinc is softer than steel but works well on heavier vehicles because it tends not to work its way loose which sometimes happens with steel wedges. The zinc holds up well too. The only time I have seen one fail is on a cement truck. That was a little too much weight!
_________________ You will not see me cry because I do not sing the blues |
| Tue Jun 04, 2013 8:23 am |
|
|
|
|
Official CCB Member Joined: Fri Oct 14, 2011 12:16 am Posts: 3942 Location: Denver, Wash Park Area
|
Re: 4 degree steel shims might be interested.. i need to re-measure my angles this week I think I have too much pinion angle..
_________________ 1976 Bronco "Green, Yellow, whatever", 1969 Bronco "Red", 1972 Bronco Stocker "Kind of Blue/Grayish" |
| Tue Jun 04, 2013 8:28 am |
|
|
|
|
Official CCB Member  Joined: Tue Oct 05, 2010 10:17 pm Posts: 568 Images: 0 Location: Golden
|
Re: 4 degree steel shims How much for these risqué zinc wedges??
_________________ Your sh!* is my bread and butter! |
| Tue Jun 11, 2013 10:14 pm |
|
|
|
|
Official CCB Member Joined: Tue Jan 25, 2011 9:33 am Posts: 207 Location: Aurora, CO
|
Re: 4 degree steel shims _________________ You will not see me cry because I do not sing the blues |
| Wed Jun 12, 2013 8:40 am |
|
|
|
|
|
Page 1 of 1 |
[ 9 posts ] |
|
All times are UTC - 7 hours [ DST ] |
Who is online |
Users browsing this forum: No registered users and 71 guests |
| You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum |