|
|
It is currently Sun Nov 24, 2024 5:47 pm
|
|
Page 1 of 1
|
[ 8 posts ] |
|
| Author |
Message |
|
HIX
Official CCB Member
Joined: Tue Feb 15, 2011 12:38 pm
Posts: 174
Location: Wheat Ridge Colorado
|
 cheap a$$ family cage 20130813_165451.jpg
Here is my combo slice of a 4 pt smittybilt rollbar and a 6pt smittybilt front cage (thx gunnibronco) into a passable family cage
20130813_173051.jpg
You do not have the required permissions to view the files attached to this post.
|
| Tue Aug 13, 2013 5:04 pm |
|
|
|
Gunnibronco
Official CCB Member
Joined: Mon Jan 03, 2011 6:07 pm
Posts: 4074
Location: Gardnerville, NV
|
Re: cheap a$$ family cage Looks good. Glad its getting reused, and not cut up for other projects.
Did it fit well? Sit flat on the floor? Just wondering how whacked out my tub is.
_________________
"America is at that awkward stage. It's too late to work within the system, but too early to shoot the bastards." – Claire Wolfe
74-AWB 98", ZF5, Atlas4, TGW HP1060 and HP1014 axles, ARBs, 37's, 3.5" lift-5.5" front coil springs, Tahoe rear springs, EFI 302, h-boost, York OBA, 4x4x2, custom dash & gauges
72 U15- Explorer Sport-Candyapple Red (1 of 141)
|
| Tue Aug 13, 2013 5:34 pm |
|
|
|
HIX
Official CCB Member
Joined: Tue Feb 15, 2011 12:38 pm
Posts: 174
Location: Wheat Ridge Colorado
|
Re: cheap a$$ family cage Using my existing roll bar holes the front was above the floor by 3/4 to one inch
|
| Tue Aug 13, 2013 6:05 pm |
|
|
|
Gunnibronco
Official CCB Member
Joined: Mon Jan 03, 2011 6:07 pm
Posts: 4074
Location: Gardnerville, NV
|
Re: cheap a$$ family cage That could be because I put it in after welding in new front floor pans. My body crossmembers (under the driver & passenger feet) were cracked & bent from the body mount out, on both sides. I used a jack, a BFH, angle iron, and a welder, to try to straighten them before putting the new floors in, but I bet they didn't go back in just right.
_________________
"America is at that awkward stage. It's too late to work within the system, but too early to shoot the bastards." – Claire Wolfe
74-AWB 98", ZF5, Atlas4, TGW HP1060 and HP1014 axles, ARBs, 37's, 3.5" lift-5.5" front coil springs, Tahoe rear springs, EFI 302, h-boost, York OBA, 4x4x2, custom dash & gauges
72 U15- Explorer Sport-Candyapple Red (1 of 141)
|
| Tue Aug 13, 2013 6:10 pm |
|
|
|
HIX
Official CCB Member
Joined: Tue Feb 15, 2011 12:38 pm
Posts: 174
Location: Wheat Ridge Colorado
|
Re: cheap a$$ family cage It actually worked out great for me since I tightened all the rear 4 legs first then cranked down the front and it closed the 1/4 inch extra gap I had at top of the door
|
| Tue Aug 13, 2013 9:19 pm |
|
|
|
Gunnibronco
Official CCB Member
Joined: Mon Jan 03, 2011 6:07 pm
Posts: 4074
Location: Gardnerville, NV
|
Re: cheap a$$ family cage
_________________
"America is at that awkward stage. It's too late to work within the system, but too early to shoot the bastards." – Claire Wolfe
74-AWB 98", ZF5, Atlas4, TGW HP1060 and HP1014 axles, ARBs, 37's, 3.5" lift-5.5" front coil springs, Tahoe rear springs, EFI 302, h-boost, York OBA, 4x4x2, custom dash & gauges
72 U15- Explorer Sport-Candyapple Red (1 of 141)
|
| Wed Aug 14, 2013 7:38 am |
|
|
|
phyler
Official CCB Member
Joined: Sat Oct 02, 2010 9:41 pm
Posts: 1201
Location: Erie
|
Re: cheap a$$ family cage HIX, I would love to see this up close and pick your brain some. I had a few ideas similar to this for the rear. Curious why you kept the original rear legs versus just building new stretchers on the top.
Adam
Sent from my HTC One using Tapatalk 2
_________________
1975 Ranger Edition that I've had longer than I've been without it.
|
| Wed Aug 14, 2013 5:54 pm |
|
|
|
HIX
Official CCB Member
Joined: Tue Feb 15, 2011 12:38 pm
Posts: 174
Location: Wheat Ridge Colorado
|
Re: cheap a$$ family cage The hoop would have been too close to the tailgate and the top would not have fit. You cant just slide the hoop forward to the rear of the wheelwell because of the filler tube box out on the driver's side.
I wanted to build this with no bending, just cutting and welding. Ill probably add spreaders on top at some point
|
| Wed Aug 14, 2013 9:08 pm |
|
|
|
|
|
Page 1 of 1
|
[ 8 posts ] |
|
Who is online |
Users browsing this forum: Google [Bot] and 29 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
