|
|
It is currently Sun Nov 24, 2024 4:40 pm
|
|
Page 1 of 1
|
[ 6 posts ] |
|
Full width track bar options
| Author |
Message |
|
akaFrankCastle
Official CCB Member
Joined: Wed Oct 27, 2010 6:25 pm
Posts: 4901
Images: 0
Location: Colorado Springs
|
 Full width track bar options Let me preface this by saying I do not plan to run full widths. However, the Baja is currently sitting on them to make it a roller. And the future owner of the full widths will likely have the same question if I don't line up a solution prior to him taking ownership.
So, for the guys running full widths, what are you using for track bars? What modifications were required? What kind of cost was associated?
TIA
_________________
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
|
| Mon Feb 16, 2015 3:13 pm |
|
|
|
Dirtheadz
Official CCB Member
Joined: Thu Jan 27, 2011 9:27 pm
Posts: 929
Location: Colorad Springs
|
Re: Full width track bar options DOM & heims w/ misallignment spacers. I think I have $60 into mine
_________________
!!! Being original is a blueprint for followers !!!
|
| Mon Feb 16, 2015 4:49 pm |
|
|
|
Justin
Official CCB Member
Joined: Sun Oct 10, 2010 12:04 am
Posts: 6198
Images: 0
Location: Lakewood
|
Re: Full width track bar options DOM and heim on one end. Haven't worked out the other end yet, as I want to run a bushing to give a little give and haven't found a solution that brings me enough joy. I'd agree with the $60 estimate. I may wind up with a spare piece of DOM. No mods. I thought I'd need a bend in the track bar due to above average up-travel, but I think I gained enough oil pan room with the change in motor mounts and slight drop at the upper track bar bracket.
|
| Mon Feb 16, 2015 5:04 pm |
|
|
|
Gunnibronco
Official CCB Member
Joined: Mon Jan 03, 2011 6:07 pm
Posts: 4074
Location: Gardnerville, NV
|
Re: Full width track bar options I cut off the frame end of my stock track bar & welded DOM with 1" ID (I think I remember right) added a bung & heim joint at the frame end. I had to slightly grind down the stock bar a little to slide into the DOM.
Pretty cheap.
You do not have the required permissions to view the files attached to this post.
_________________
"America is at that awkward stage. It's too late to work within the system, but too early to shoot the bastards." – Claire Wolfe
74-AWB 98", ZF5, Atlas4, TGW HP1060 and HP1014 axles, ARBs, 37's, 3.5" lift-5.5" front coil springs, Tahoe rear springs, EFI 302, h-boost, York OBA, 4x4x2, custom dash & gauges
72 U15- Explorer Sport-Candyapple Red (1 of 141)
|
| Mon Feb 16, 2015 7:13 pm |
|
|
|
Digger
Official CCB Member
Joined: Fri Jun 21, 2013 8:53 pm
Posts: 1276
|
Re: Full width track bar options
_________________
Cummins R2.8 diesel, ZF5, AtlasII, HP44/BB9, ARBs, coiled / linked suspension, 37" KO2s, full cage, bumpers, etc.
Build Thread:
Average 23.5 mpg, Best tank: 25.1 mpg
|
| Fri Feb 20, 2015 4:24 pm |
|
|
|
RJLougee
Official CCB Member
Joined: Thu Sep 30, 2010 1:40 pm
Posts: 215
Images: 0
Location: Falcon, CO
|
Re: Full width track bar options I take the existing EB track bar and cut/grind/weld in the adjustable section of a large set of tie rods, like SD size. They can be had pretty cheap from the 'yards and allow you to adjust where the axle tracks as springs sag, etc...
Joe
_________________
'70 Bronco, MAF 5.0, NP435, D44/9", 4.10s, 33" MT/Rs, PS/PB
'71 Bronco, HP D60, Hi-9, 5.38/ARBs, 101" WB, 408 Stroker, AOD, Atlas, 40" MT/Rs, PiMP EFI.
'78 F150 SWB/Stepside/4WD, 351W/4R100/NP205, 35" KM2s, under const...
'81 Coachman Caper XL MH, 4WD, EFI 460/ZF/BW1356, D44/Sterling, 4.10s/35s, under const...
'83 Bronco, D60/Sterling, 5.13/ARBs, MAF EFI 351W/ZF/BW1356, 37" MT/Rs.
'12 Buggy, HPD60, Hi-9, 4.10s, Explorer 5.0, Atlas 4-speed, my chassis, EB skins.
And the latest project is a '99 Ranger Extra-Cab, custom frame/tube work, on 40s...
|
| Sat Feb 21, 2015 5:37 pm |
|
|
|
|
|
Page 1 of 1
|
[ 6 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 24 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
