|
It is currently Fri Nov 22, 2024 6:58 pm |
|
All times are UTC - 7 hours [ DST ] |
|
Page 1 of 1 |
[ 5 posts ] |
| Previous topic | Next topic |
11ga sheet metal
| Author | Message |
|---|---|
|
Official CCB Member   Joined: Thu Nov 11, 2010 10:36 am Posts: 5984 Location: California 
|
 11ga sheet metalAnyone want to split a 4x8 sheet of 11ga with me? That's nearly 1/8" thick. It's $110+tax. I just don't think I need the whole sheet. I have not bought it yet, but hope to on Friday. Thanks!
J.D. _________________ 1973 Bronco, 351 SEFI, Locked, discs, 35's ZF-5spd and Atlas 4spd. 235:1 Crawl Ratio. It may be ugly, but it's slow. http://www.ucora.org |
| Tue Apr 05, 2011 4:10 pm |
|
|
|
|
Official CCB Member  Joined: Wed Oct 27, 2010 6:25 pm Posts: 4901 Images: 0 Location: Colorado Springs
|
Re: 11ga sheet metal Whatcha thinking about making out of this? I might be interested in going in. Can always use some sheet for projects and what not.
_________________ Stroppe'd 1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar. The Terrible One 1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering. 1973 Stroppe Baja project |
| Tue Apr 05, 2011 5:17 pm |
|
|
|
|
Official CCB Member Joined: Thu Nov 11, 2010 10:36 am Posts: 5984 Location: California
|
Re: 11ga sheet metal _________________ 1973 Bronco, 351 SEFI, Locked, discs, 35's ZF-5spd and Atlas 4spd. 235:1 Crawl Ratio. It may be ugly, but it's slow. http://www.ucora.org |
| Tue Apr 05, 2011 5:39 pm |
|
|
|
|
Official CCB Member Joined: Wed Oct 27, 2010 6:25 pm Posts: 4901 Images: 0 Location: Colorado Springs
|
Re: 11ga sheet metal I'm in NC at the moment. But if you pull the trigger, I'm good for half.
_________________ Stroppe'd 1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar. The Terrible One 1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering. 1973 Stroppe Baja project |
| Tue Apr 05, 2011 9:50 pm |
|
|
|
|
Official CCB Member Joined: Thu Nov 11, 2010 10:36 am Posts: 5984 Location: California
|
Re: 11ga sheet metal Cool. I'll plan on it then and keep it rust free until we can connect.
I will let you know for sure. Thanks! J.D. _________________ 1973 Bronco, 351 SEFI, Locked, discs, 35's ZF-5spd and Atlas 4spd. 235:1 Crawl Ratio. It may be ugly, but it's slow. http://www.ucora.org |
| Wed Apr 06, 2011 7:17 am |
|
|
|
|
|
Page 1 of 1 |
[ 5 posts ] |
|
All times are UTC - 7 hours [ DST ] |
Who is online |
Users browsing this forum: No registered users and 1 guest |
| You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum |