|
It is currently Sun Nov 24, 2024 10:37 pm |
|
All times are UTC - 7 hours [ DST ] |
|
Page 1 of 1 |
[ 5 posts ] |
| Print view | Previous topic | Next topic |
Cutting oil
| Author | Message |
|---|---|
|
Official CCB Member   Joined: Sun Oct 10, 2010 12:04 am Posts: 6198 Images: 0 Location: Lakewood 
|
 Cutting oilNeed to get some cutting oil so that I don't destroy Zoso's reamer tomorrow when I reinstall my tie rod. Home Depot doesn't carry it, Ace's is supposed to be really bad. Any suggestions about where to pick up some cutting oil of decent quality, ideally in the northern half of the metro area?
|
| Mon May 23, 2011 9:55 pm |
|
|
|
|
Moderator   Joined: Mon Nov 15, 2010 5:58 pm Posts: 3906 Location: Henderson, Co
|
Re: Cutting oil I've got a big bottle too. Ill be at my dads after work if you wanna get it. He lives a few blocks west from dan.
_________________ Rob 74 Ranger EFI351w, 4r70w, ARB 5.13 9in, ARB 5.13D44, and a bunch of other goodies. Best of all the family memories. 04 Mustang Cobra, KenneBell 2.2 feeding a lot of boost on E85. Tire shredding machine New project: 77 Bronco Ranger, body work and more body work. Very little left of a 72 durango tan explorer sport |
| Tue May 24, 2011 6:13 am |
|
|
|
|
Official CCB Member  Joined: Thu Nov 11, 2010 10:36 am Posts: 5984 Location: California
|
Re: Cutting oil Also, the trick with the reamer is to go very very slow. I've had better results from using a ratchet by hand than a drill.
J.D. _________________ 1973 Bronco, 351 SEFI, Locked, discs, 35's ZF-5spd and Atlas 4spd. 235:1 Crawl Ratio. It may be ugly, but it's slow. http://www.ucora.org |
| Tue May 24, 2011 8:20 am |
|
|
|
|
Official CCB Member Joined: Thu Nov 11, 2010 10:36 am Posts: 5984 Location: California
|
Re: Cutting oil Yep. Seems the smaller bits >3/8" or so do fine with higher speeds, but anything above that and I slow it down!
J.D. _________________ 1973 Bronco, 351 SEFI, Locked, discs, 35's ZF-5spd and Atlas 4spd. 235:1 Crawl Ratio. It may be ugly, but it's slow. http://www.ucora.org |
| Tue May 24, 2011 8:39 am |
|
|
|
|
Official CCB Member Joined: Sun Oct 10, 2010 12:04 am Posts: 6198 Images: 0 Location: Lakewood
|
Re: Cutting oil Thanks for the advice and offers, guys. I was able to find some while I was down in Denver today. Hope to get it done today or tomorrow.
|
| Tue May 24, 2011 7:10 pm |
|
|
|
|
|
Page 1 of 1 |
[ 5 posts ] |
|
All times are UTC - 7 hours [ DST ] |
Who is online |
Users browsing this forum: No registered users and 48 guests |
| You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum |