| www.ColoradoClassicBroncos.com https://coloradoclassicbroncos.com/ |
|
| Need a bit of help https://coloradoclassicbroncos.com/viewtopic.php?f=4&t=5897 |
Page 1 of 1 |
| Author: | landshark [ Wed Jan 15, 2014 10:07 pm ] |
| Post subject: | Need a bit of help |
I know most are going to the breakfast on sat, I might make it depending on how much I get done on my bronco tomorrow and fri, however I could really use a couple of hours of help if someone is around Friday late afternoon/evening. I will probably have the majoirty of the parts I need to get the zf in place, however still waiting on the adapater which might be in fri or monday.. not sure yet. I do need to fab up a cross brace but I haven't had a chance to get to the steel yard yet and would just be happy to have the zf in place for now.. Anyway if anyone can swing by on friday let me know, I will provide grub and drinks of course.. let me know thanks guys. |
|
| Author: | Rox Crusher [ Wed Jan 15, 2014 10:09 pm ] |
| Post subject: | Re: Need a bit of help |
I believe I can help in Friday afternoon (late) if that helps ? |
|
| Author: | landshark [ Wed Jan 15, 2014 10:14 pm ] |
| Post subject: | Re: Need a bit of help |
| Author: | Viperwolf1 [ Wed Jan 15, 2014 10:19 pm ] |
| Post subject: | Re: Need a bit of help |
I can help on Friday. Do you need a jack? |
|
| Author: | landshark [ Wed Jan 15, 2014 10:20 pm ] |
| Post subject: | Re: Need a bit of help |
nope, bought a fancy transmission jack so good there. I work most of the day but can get off around 2pm |
|
| Author: | Viperwolf1 [ Wed Jan 15, 2014 10:22 pm ] |
| Post subject: | Re: Need a bit of help |
Good, mine scares me. |
|
| Author: | Rox Crusher [ Wed Jan 15, 2014 10:48 pm ] |
| Post subject: | Re: Need a bit of help |
Yes, I can bring my welder |
|
| Author: | landshark [ Wed Jan 15, 2014 11:07 pm ] |
| Post subject: | Re: Need a bit of help |
ok cool.. i will plan on being in the garage by 4.. i will try to get to the metal yard around lunch time and grab some steel.. not sure I/we will have time to make a cross member but just in case.. |
|
| Author: | Kinder [ Thu Jan 16, 2014 11:09 am ] |
| Post subject: | Re: Need a bit of help |
The boys & I are going to the ISE Friday morning, we can stop by in the afternoon. |
|
| Author: | landshark [ Thu Jan 16, 2014 11:37 am ] |
| Post subject: | Re: Need a bit of help |
cool ping me to make sure Iam around! thanks guys |
|
| Author: | landshark [ Fri Jan 17, 2014 9:25 am ] |
| Post subject: | Re: Need a bit of help |
I should be in the garage by 3:30 today. Doesn't look like I will get to the scrap/metal yard and even if i did I dont think i have the bushing to make a mount for the ZF.. If anyone has a inch pound torque wrench maybe bring it along? I have everything else I think to finish the swap.. or get close anyway PM me if you need my address or # but I will have the garage open out back and i can probably fit 1 or 2 broncos in front of the garage.. |
|
| Author: | Viperwolf1 [ Fri Jan 17, 2014 10:46 am ] |
| Post subject: | Re: Need a bit of help |
I have an in-lb torque wrench I'll bring. It doesn't read very high though. What torque spec are you looking for? |
|
| Author: | landshark [ Fri Jan 17, 2014 10:49 am ] |
| Post subject: | Re: Need a bit of help |
| Author: | Dirtheadz [ Fri Jan 17, 2014 1:02 pm ] |
| Post subject: | Re: Need a bit of help |
if you were closer, I wouldnt mind helping.... sorry! Depending on how your doing the crossmember I do have a bender with 1", 1-1/4", 1-1/2" & 2" dies and some misc. urathane bushing. I know it doesnt help getting you to the breakfast, just saying. Let me know |
|
| Author: | Rox Crusher [ Sat Jan 18, 2014 6:08 pm ] |
| Post subject: | Re: Need a bit of help |
Chris, how did you make out today or are you still at the bar ? |
|
| Author: | akaFrankCastle [ Sat Jan 18, 2014 6:26 pm ] |
| Post subject: | Re: Need a bit of help |
They're still loading the Thingsmajig on to the trailer. |
|
| Author: | landshark [ Sat Jan 18, 2014 8:58 pm ] |
| Post subject: | Re: Need a bit of help |
| Page 1 of 1 | All times are UTC - 7 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|