|
It is currently Mon Nov 25, 2024 3:44 am
|
|
Page 1 of 1
|
[ 8 posts ] |
|
Author |
Message |
Gunnibronco
Official CCB Member
Joined: Mon Jan 03, 2011 6:07 pm Posts: 4074 Location: Gardnerville, NV
|
P/S pump improvement
I'm plumbing my P/S, h-boost & 4x4x2 box with AN hose. I'm installing a new pump body into a dual return reservoir. I know I've read there is a way to increase the pump output, but can't find it now.
I've run h-boost for years, but am upgrading to the 4x4x2 box, dual return & a p/s cooler. I'm planning to add hydro assist in the future, but not now.
Very rarely, with my old set up, the power steering would be dead right after start up, so I figure now is a good time to put a new pump in. I recently bought a used/never run WH pump & bracket planning to put it into my 72. But I figured I'd rob the pump from it and put it into my 74.
_________________ "America is at that awkward stage. It's too late to work within the system, but too early to shoot the bastards." – Claire Wolfe 74-AWB 98", ZF5, Atlas4, TGW HP1060 and HP1014 axles, ARBs, 37's, 3.5" lift-5.5" front coil springs, Tahoe rear springs, EFI 302, h-boost, York OBA, 4x4x2, custom dash & gauges 72 U15- Explorer Sport-Candyapple Red (1 of 141)
|
Sat Mar 17, 2018 4:48 pm |
|
|
Gunnibronco
Official CCB Member
Joined: Mon Jan 03, 2011 6:07 pm Posts: 4074 Location: Gardnerville, NV
|
Re: P/S pump improvement
Ok, so why would the new reservoir only have 1 bolt holding it to the pump? The Tom's pump & WH pump use 2. I figure I need to drill a second hole & use both bolts. Or will it be ok with only 1 bolt?
And the WH pump uses metric hardware to attach the pump to the reservoir & bracket, but the old Tom's uses standard hardware. Just different stock applications?
New reservoir: DSCN8284.JPG
WH reservoir: DSCN8285.JPG
Toms DSCN8286.JPG
You do not have the required permissions to view the files attached to this post.
_________________ "America is at that awkward stage. It's too late to work within the system, but too early to shoot the bastards." – Claire Wolfe 74-AWB 98", ZF5, Atlas4, TGW HP1060 and HP1014 axles, ARBs, 37's, 3.5" lift-5.5" front coil springs, Tahoe rear springs, EFI 302, h-boost, York OBA, 4x4x2, custom dash & gauges 72 U15- Explorer Sport-Candyapple Red (1 of 141)
|
Sat Mar 17, 2018 5:14 pm |
|
|
pgilbeau
Official CCB Member
Joined: Sun Jul 07, 2013 6:06 pm Posts: 639 Location: Falcon, CO
|
Re: P/S pump improvement
If I remember right I was going to carefully drill a second hole, I never understood that either because the pump had the threads. Also I believe the later p-pumps were metric vs. the older standard ones.
_________________ 1969 Bronco: Full widths, 3 linked front end, 37's, hydro-boost, 4x4x2 box, ZF5, Atlas t-case, and fuel injected 302
|
Sat Mar 17, 2018 7:05 pm |
|
|
Gunnibronco
Official CCB Member
Joined: Mon Jan 03, 2011 6:07 pm Posts: 4074 Location: Gardnerville, NV
|
Re: P/S pump improvement
You can see the spot where it would be drilled. I was wondering if 1 bolt & the outlet fitting was adequate. I'm guessing there was some application with that set up, and it probably worked. What is a p-pump vs the older pump? Are they higher output? Is it the Delphi pump WH is advertising? I've emailed them to see if they can ID my pump as a Delphi vs Saginaw. I didn't know there were 2 versions. https://www.wildhorses4x4.com/product/H ... ring_PumpsMine looks like this one, but the shaft measures .690 at the end (pulley is installed), not .75. I assume the shaft is tapered, and I don't know where it's measured from.
_________________ "America is at that awkward stage. It's too late to work within the system, but too early to shoot the bastards." – Claire Wolfe 74-AWB 98", ZF5, Atlas4, TGW HP1060 and HP1014 axles, ARBs, 37's, 3.5" lift-5.5" front coil springs, Tahoe rear springs, EFI 302, h-boost, York OBA, 4x4x2, custom dash & gauges 72 U15- Explorer Sport-Candyapple Red (1 of 141)
|
Sat Mar 17, 2018 7:44 pm |
|
|
pgilbeau
Official CCB Member
Joined: Sun Jul 07, 2013 6:06 pm Posts: 639 Location: Falcon, CO
|
Re: P/S pump improvement
_________________ 1969 Bronco: Full widths, 3 linked front end, 37's, hydro-boost, 4x4x2 box, ZF5, Atlas t-case, and fuel injected 302
|
Sat Mar 17, 2018 9:10 pm |
|
|
ZOSO
Moderator
Joined: Mon Nov 15, 2010 5:58 pm Posts: 3906 Location: Henderson, Co
|
Re: P/S pump improvement
_________________ Rob
74 Ranger EFI351w, 4r70w, ARB 5.13 9in, ARB 5.13D44, and a bunch of other goodies. Best of all the family memories.
04 Mustang Cobra, KenneBell 2.2 feeding a lot of boost on E85. Tire shredding machine
New project: 77 Bronco Ranger, body work and more body work.
Very little left of a 72 durango tan explorer sport
|
Sat Mar 17, 2018 9:29 pm |
|
|
Gunnibronco
Official CCB Member
Joined: Mon Jan 03, 2011 6:07 pm Posts: 4074 Location: Gardnerville, NV
|
Re: P/S pump improvement
_________________ "America is at that awkward stage. It's too late to work within the system, but too early to shoot the bastards." – Claire Wolfe 74-AWB 98", ZF5, Atlas4, TGW HP1060 and HP1014 axles, ARBs, 37's, 3.5" lift-5.5" front coil springs, Tahoe rear springs, EFI 302, h-boost, York OBA, 4x4x2, custom dash & gauges 72 U15- Explorer Sport-Candyapple Red (1 of 141)
|
Sat Mar 17, 2018 11:41 pm |
|
|
Justin
Official CCB Member
Joined: Sun Oct 10, 2010 12:04 am Posts: 6198 Images: 0 Location: Lakewood
|
Re: P/S pump improvement
I did this on my Saginaw, including drilling out the hole. It worked great with the 4x4x2 box and hydroboost, but couldn't always keep up at low speeds after I added the ram. Parking lots where I used the brakes sometimes meant diminished power steering.
|
Sun Mar 18, 2018 12:24 am |
|
|
|
|
Page 1 of 1
|
[ 8 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 19 guests |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
|
|