|
|
It is currently Mon Nov 25, 2024 2:32 am
|
|
Page 1 of 1
|
[ 4 posts ] |
|
proper metal cutting tool recomendations
| Author |
Message |
|
Stubborn3
Official CCB Member
Joined: Mon Sep 17, 2012 3:09 am
Posts: 174
Location: Denver/Leadville, Coloradical
|
 proper metal cutting tool recomendations Hey all, My Transfer case refuses to go into 4 high and it appears to be contacting the floor so I need to make some room. What would work best to open up the hole in floor to allow this thing to move? I just inherited a bandfile 1/2" wide belt sander from work... would a cutting wheel on that be enough? Thanks as always
_________________
'72 sport, 351 Cleveland, NP435, twin-sticked 20, unknown lift- if any, 35" KM2s siped by B.O.B, custom rust and dents, 2 kid seats.
|
| Sun Dec 16, 2012 4:29 am |
|
|
|
kchaser
Official CCB Member
Joined: Sat May 07, 2011 5:54 pm
Posts: 269
Location: Wellington
|
Re: proper metal cutting tool recomendations What about bending the shifter shaft back some so it doesn't contact the floor? Just a thought.
|
| Sun Dec 16, 2012 8:46 am |
|
|
|
Gunnibronco
Official CCB Member
Joined: Mon Jan 03, 2011 6:07 pm
Posts: 4074
Location: Gardnerville, NV
|
Re: proper metal cutting tool recomendations I'd guess the 3" grinder on the sander would work, if it can take a grinder wheel. Lots of other choices, if you want to buy a tool or two. 3" or 4" grinder, jig saw, air saw, nibbler, etc.
Do you have a body lift? The added body lift can make the floor & stick interfere. If not, the shifter might be getting old and need rebuilt/replaced. That was my case & I ended up twin sticking it.
Good luck
Chad
_________________
"America is at that awkward stage. It's too late to work within the system, but too early to shoot the bastards." – Claire Wolfe
74-AWB 98", ZF5, Atlas4, TGW HP1060 and HP1014 axles, ARBs, 37's, 3.5" lift-5.5" front coil springs, Tahoe rear springs, EFI 302, h-boost, York OBA, 4x4x2, custom dash & gauges
72 U15- Explorer Sport-Candyapple Red (1 of 141)
|
| Sun Dec 16, 2012 9:02 am |
|
|
|
Stubborn3
Official CCB Member
Joined: Mon Sep 17, 2012 3:09 am
Posts: 174
Location: Denver/Leadville, Coloradical
|
Re: proper metal cutting tool recomendations I do intend to twin stick it after Christmas... just need to get through any snow before then. It does not have a body lift as far as I can tell but it has the Duff shifter which is sort of rectangular and odd. I would have preferred to just bend it but oh well. Gonna get some better tools... got a lot of other bodywork to do anyways. Thanks
_________________
'72 sport, 351 Cleveland, NP435, twin-sticked 20, unknown lift- if any, 35" KM2s siped by B.O.B, custom rust and dents, 2 kid seats.
|
| Sun Dec 16, 2012 3:04 pm |
|
|
|
|
|
Page 1 of 1
|
[ 4 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 34 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
