|
|
Register •
FAQ
• Login
|
|
|
It is currently Fri Nov 22, 2024 2:03 am
|
|
Page 1 of 1
|
[ 6 posts ] |
|
| Author |
Message |
|
Kerapsak
Official CCB Member
Joined: Thu Mar 15, 2012 7:24 pm
Posts: 26
Images: 0
Location: Berthoud
|
 Rear axle not going in I replaced rear axle oil seals and now the driver side is not going in all the way. It is connecting because both axles spin but it has about the bearing width to go. Passenger went in just fine. Any tricks to this?
|
| Sun Feb 07, 2021 5:40 pm |
|
|
|
ZOSO
Moderator
Joined: Mon Nov 15, 2010 5:58 pm
Posts: 3906
Location: Henderson, Co
|
Re: Rear axle not going in did you mix up the sides? one is shorter than the other.
_________________
Rob
74 Ranger EFI351w, 4r70w, ARB 5.13 9in, ARB 5.13D44, and a bunch of other goodies. Best of all the family memories.
04 Mustang Cobra, KenneBell 2.2 feeding a lot of boost on E85. Tire shredding machine
New project: 77 Bronco Ranger, body work and more body work.
Very little left of a 72 durango tan explorer sport
|
| Sun Feb 07, 2021 6:46 pm |
|
|
|
Kerapsak
Official CCB Member
Joined: Thu Mar 15, 2012 7:24 pm
Posts: 26
Images: 0
Location: Berthoud
|
Re: Rear axle not going in I thought maybe that was it but it is the short side. When I drained the oil I spun it without the axles in which I guess I shouldn’t have.
|
| Sun Feb 07, 2021 7:21 pm |
|
|
|
landshark
Official CCB Member
Joined: Fri Oct 14, 2011 12:16 am
Posts: 3942
Location: Denver, Wash Park Area
|
Re: Rear axle not going in Spinning it has no impact on the spline engagement. Either the axles are swapped or you just need to rotate the axle shaft a little until it engages fully
_________________
1976 Bronco "Green, Yellow, whatever", 1969 Bronco "Red", 1972 Bronco Stocker "Kind of Blue/Grayish"
|
| Sun Feb 07, 2021 7:48 pm |
|
|
|
Viperwolf1
Official CCB Member
Joined: Tue May 07, 2013 10:37 pm
Posts: 1485
|
Re: Rear axle not going in Is it a factory limited slip diff? There are 2 sets of splines on one side. They can become unaligned when pulling the axles out. Trick is to put the other side together and set it on the tire so it cant move. Then you can twist the other axle a little to get the splines lined up.
|
| Sun Feb 07, 2021 9:30 pm |
|
|
|
Kerapsak
Official CCB Member
Joined: Thu Mar 15, 2012 7:24 pm
Posts: 26
Images: 0
Location: Berthoud
|
Re: Rear axle not going in It is limited slip and that trick worked. Thank you Viper!!
|
| Sun Feb 07, 2021 11:41 pm |
|
|
|
|
|
Page 1 of 1
|
[ 6 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 12 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
