|
|
It is currently Thu Nov 21, 2024 3:55 pm
|
|
Page 1 of 1
|
[ 3 posts ] |
|
Coolant outlet for Edelbrock Performer
| Author |
Message |
|
akaFrankCastle
Official CCB Member
Joined: Wed Oct 27, 2010 6:25 pm
Posts: 4901
Images: 0
Location: Colorado Springs
|
 Coolant outlet for Edelbrock Performer Install of the new intake and carb is on hold at the moment. Looking for a 90* coolant outlet for the front of my intake. This would be the piece where the coolant exits the intake and heads to the heater. Looks to be about 1/2" OD. I'd pull the one from the old intake, but the OD is smaller on that one. Looks to be about 3/8"
_________________
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
|
| Wed Apr 20, 2011 6:53 pm |
|
|
|
crawlercreations
Official CCB Member
Joined: Sat Nov 06, 2010 9:36 pm
Posts: 1101
Location: Arvada
|
Re: Coolant outlet for Edelbrock Performer Brass fitting at ACE hardware or similar should fix you up. Should just be pipe thread in the intake and a bard fitting on the end for the hose. I found one for my last intake at ACE hardware.
_________________
There is a fine line between "hobby" and "mental illness"
|
| Wed Apr 20, 2011 7:38 pm |
|
|
|
akaFrankCastle
Official CCB Member
Joined: Wed Oct 27, 2010 6:25 pm
Posts: 4901
Images: 0
Location: Colorado Springs
|
Re: Coolant outlet for Edelbrock Performer Word. Didn't even think to check ACE.
_________________
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
|
| Wed Apr 20, 2011 8:03 pm |
|
|
|
|
|
Page 1 of 1
|
[ 3 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 12 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
