|
It is currently Mon Nov 25, 2024 12:51 am |
|
All times are UTC - 7 hours [ DST ] |
|
Page 1 of 1 |
[ 7 posts ] |
| Print view | Previous topic | Next topic |
Top Molding
| Author | Message |
|---|---|
|
Official CCB Member   Joined: Wed Sep 29, 2010 5:45 pm Posts: 3275 Location: Gilbert, Arizona 
|
 Top MoldingAnyone put a weather strip or seal on the bed rails to protect the paint before installing hard top or soft top?
_________________ "I truly believe that good will outweigh evil, but there won't be peace on earth until the power of love overcomes the love of power" - Jimi Hendrix |
| Wed May 18, 2011 8:21 pm |
|
|
|
|
Official CCB Member  Joined: Sun Oct 10, 2010 11:33 pm Posts: 231 Images: 5 Location: Greeley, CO
|
Re: Top Molding Ours has the factory seal. Still had some marks when it was removed, but it had been on for 25+ years.
|
| Wed May 18, 2011 8:44 pm |
|
|
|
|
Official CCB Member  Joined: Thu Nov 11, 2010 10:36 am Posts: 5984 Location: California
|
Re: Top Molding You might consider ordering some rubber strips from mcmaster. That would both protect and seal.
J.D. _________________ 1973 Bronco, 351 SEFI, Locked, discs, 35's ZF-5spd and Atlas 4spd. 235:1 Crawl Ratio. It may be ugly, but it's slow. http://www.ucora.org |
| Thu May 19, 2011 9:01 am |
|
|
|
|
Official CCB Member Joined: Wed Sep 29, 2010 5:45 pm Posts: 3275 Location: Gilbert, Arizona
|
Re: Top Molding I have not checked with mcmaster - great idea!
_________________ "I truly believe that good will outweigh evil, but there won't be peace on earth until the power of love overcomes the love of power" - Jimi Hendrix |
| Thu May 19, 2011 9:03 am |
|
|
|
|
Official CCB Member Joined: Thu Nov 11, 2010 10:36 am Posts: 5984 Location: California
|
Re: Top Molding I needed some to space the top away from the bedrails so my soft doors would fit. I ordered 1/4" thick, but you'd go with much thinner. And the softer stuff will crush better.
J.D. _________________ 1973 Bronco, 351 SEFI, Locked, discs, 35's ZF-5spd and Atlas 4spd. 235:1 Crawl Ratio. It may be ugly, but it's slow. http://www.ucora.org |
| Thu May 19, 2011 9:13 am |
|
|
|
|
Joined: Fri Oct 15, 2010 8:25 pm Posts: 4
|
Re: Top Molding would camper seal tape work ?? Has a peel back adhesive on one side, made out of foam rubber. Any RV place would have it.
|
| Thu May 19, 2011 7:06 pm |
|
|
|
|
Official CCB Member  Joined: Wed Oct 06, 2010 10:04 am Posts: 740 Images: 0
|
Re: Top Molding watch out using neoprene, I have used it and it messes with the crush factor. The doors won't seal & you will have gaps all over the place. Get some really soft rubber or buy the OEM ones from JBG
|
| Fri May 20, 2011 9:38 am |
|
|
|
|
|
Page 1 of 1 |
[ 7 posts ] |
|
All times are UTC - 7 hours [ DST ] |
Who is online |
Users browsing this forum: No registered users and 52 guests |
| You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum |