|
|
It is currently Mon Nov 25, 2024 12:57 am
|
|
Page 1 of 1
|
[ 8 posts ] |
|
3 speed manual wont go into 2-3
| Author |
Message |
|
socofn
Official CCB Member
Joined: Sat Apr 02, 2011 11:52 am
Posts: 204
Images: 0
Location: Pueblo County
|
 3 speed manual wont go into 2-3 Finally got everything back in and now it won't go into 2-3. It a 3speed on the collum and the linkage is free. I can move 1-reverse by hand but 2-3 wont budge and I do not want to put to much pressure on it. Suggestion are greatly apperciated. JP
_________________
74, MONEY EATER
|
| Sat Jun 16, 2012 6:44 am |
|
|
|
akaFrankCastle
Official CCB Member
Joined: Wed Oct 27, 2010 6:25 pm
Posts: 4901
Images: 0
Location: Colorado Springs
|
3 speed manual wont go into 2-3 If your trans is toast, let me know. I have two organ donors in the garage you can pick apart.
_________________
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
|
| Sat Jun 16, 2012 12:32 pm |
|
|
|
Booger
Official CCB Member
Joined: Thu Dec 23, 2010 6:55 pm
Posts: 809
Location: Broomfield
|
Re: 3 speed manual wont go into 2-3 You just might have to take aka up on that offer.
_________________
Bob - Turning hydrocarbons into noise since 1970
Spiritual owner of the now Zoso mobile (1974 Bronco Ranger - EFI 351W-4R70W-ARB front and rear-STC softtop- High Country hood-3 1/2" WH lift- Cross inboard rear shock mnt- Duffs bumpers- Warn 8274- 33's- Cheby disc conversion)
|
| Sat Jun 16, 2012 8:17 pm |
|
|
|
socofn
Official CCB Member
Joined: Sat Apr 02, 2011 11:52 am
Posts: 204
Images: 0
Location: Pueblo County
|
Re: 3 speed manual wont go into 2-3 I hope it isn't as it is the one I just got from airbur attached to a 302 that was working. I have not had time to mess with it since friday but if anyone has any ideas what I can do to figure this out, your input is greatly apperciated. Thanks JP
_________________
74, MONEY EATER
|
| Sun Jun 17, 2012 5:59 pm |
|
|
|
akaFrankCastle
Official CCB Member
Joined: Wed Oct 27, 2010 6:25 pm
Posts: 4901
Images: 0
Location: Colorado Springs
|
3 speed manual wont go into 2-3 Well, my first suggestion would have been to pull the top cover and have a look see at what is hanging up.
Just for giggles, you are manipulating the shift levers in a R-N-1/3-N-2 fashion, correct? Middle position being neutral, gears to either side.
_________________
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
|
| Sun Jun 17, 2012 6:21 pm |
|
|
|
socofn
Official CCB Member
Joined: Sat Apr 02, 2011 11:52 am
Posts: 204
Images: 0
Location: Pueblo County
|
Re: 3 speed manual wont go into 2-3 On the shift levers it goes freely into r-n-1 and will not move at all into 2-n-3. Pulling the top cover is going to be a PIA as it is already installed!!! I will do what I need to tho to get it back up and runnin. Thanks JP
_________________
74, MONEY EATER
|
| Sun Jun 17, 2012 9:21 pm |
|
|
|
airbur
Official CCB Member
Joined: Wed Sep 29, 2010 8:39 am
Posts: 1721
Images: 0
Location: Castle Pines, CO
|
3 speed manual wont go into 2-3 What did you do to my tranny?! I had no prob shifting it the day I took the video for you.....ran it around the city a bit to make sure everything was in good working order before I pulled it.
Maybe an issue with how the clutch linkage is setup?
_________________
Sold: 1970 w/427W Injected Stroker
|
| Mon Jun 25, 2012 9:13 pm |
|
|
|
socofn
Official CCB Member
Joined: Sat Apr 02, 2011 11:52 am
Posts: 204
Images: 0
Location: Pueblo County
|
Re: 3 speed manual wont go into 2-3 Got it figured out. Thanks JP
_________________
74, MONEY EATER
|
| Tue Jun 26, 2012 8:50 am |
|
|
|
|
|
Page 1 of 1
|
[ 8 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 30 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
