|
|
It is currently Mon Nov 25, 2024 12:53 am
|
|
Page 1 of 1
|
[ 7 posts ] |
|
| Author |
Message |
|
akaFrankCastle
Official CCB Member
Joined: Wed Oct 27, 2010 6:25 pm
Posts: 4901
Images: 0
Location: Colorado Springs
|
 GT40P's and headers Who is running GT40P's and what headers are you running with them? I remember once upon a time reading the BCB headers had a slight problem with the P's and required some clearance some be done. I was going to check out the WH selection but their site is still down.
_________________
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
|
| Tue Jul 10, 2012 8:33 am |
|
|
|
Rox Crusher
Official CCB Member
Joined: Sun Oct 10, 2010 5:36 pm
Posts: 3980
Location: Roxborough Park, Colorado
|
Re: GT40P's and headers I'm your huckleberry.
I researched this extensively before settling on BC Broncos.
It was between them and Bronco Hut. I ruled BH out as I try to avoid doing business with them when possible.
BC had to modify their headers to provide clearance for the spark plugs. They simply added a dimple to certain tubes for the really tight fitting plugs.
You still have to loosen the headers to access / service some of the plugs. I am going to swap over to a shortie plug to get away from that requirement.
_________________
1977 Sport, 351w OBDII EFI motor, 4R70W auto, 4:88 gears, ARB lockers, 3.5" suspension, 33" tires.
|
| Tue Jul 10, 2012 10:46 am |
|
|
|
jbregar
Official CCB Member
Joined: Thu Jun 07, 2012 10:10 pm
Posts: 94
Location: Pueblo West, CO
|
Re: GT40P's and headers I have the Bronco Hut headers. They work MUCH better with the 40P than the BC ones they replaced, but my BCs were from two years back so maybe Chuck's redesigned them a bit, I dunno. Mine were a pain in the ass to mount on the 40P heads and there were a few plugs I'd never have been able to get a boot on, much less replace.
The BH headers mount right up and every plug is fully accessible.
_________________
1966 Bronco (Aug. 1965 production date), 5.0L Explorer EFI, 33x12.50 BFG AT
|
| Tue Jul 10, 2012 11:53 am |
 
|
|
|
landshark
Official CCB Member
Joined: Fri Oct 14, 2011 12:16 am
Posts: 3942
Location: Denver, Wash Park Area
|
Re: GT40P's and headers what about the gt40's you pulled ;)
_________________
1976 Bronco "Green, Yellow, whatever", 1969 Bronco "Red", 1972 Bronco Stocker "Kind of Blue/Grayish"
|
| Tue Jul 10, 2012 11:55 am |
|
|
|
akaFrankCastle
Official CCB Member
Joined: Wed Oct 27, 2010 6:25 pm
Posts: 4901
Images: 0
Location: Colorado Springs
|
GT40P's and headers
_________________
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
|
| Tue Jul 10, 2012 1:12 pm |
|
|
|
landshark
Official CCB Member
Joined: Fri Oct 14, 2011 12:16 am
Posts: 3942
Location: Denver, Wash Park Area
|
Re: GT40P's and headers i hear ya.. same boat i had to have a set of heads rebuilt anyway which is why i looked for a set of the gt40's.. got lucky found a set at the first yard i went to.
from all the horror stories i have heard over the years about the P heads so I chose the reg gt40's. The performance between the two from the testing i have seen and read about was negligible. not to mention the fact the manifolds and plug problems affect the P's more than makes up for the 3% or whatever difference there really is - it just alleviates one more headache.
i know the regular GT40's are harder to find and I got lucky... there were 3 sets of P's in the yard when i was there.... might have pulled one of those had i not found this set.. honestly.. but you have a choice!
;)
_________________
1976 Bronco "Green, Yellow, whatever", 1969 Bronco "Red", 1972 Bronco Stocker "Kind of Blue/Grayish"
|
| Tue Jul 10, 2012 1:27 pm |
|
|
|
jbregar
Official CCB Member
Joined: Thu Jun 07, 2012 10:10 pm
Posts: 94
Location: Pueblo West, CO
|
Re: GT40P's and headers The Bronco Hut headers work wonderfully with the GT40Ps. If you'd like pics, let me know. My engine's on a stand right now, so I can get all the angles.
_________________
1966 Bronco (Aug. 1965 production date), 5.0L Explorer EFI, 33x12.50 BFG AT
|
| Tue Jul 10, 2012 5:30 pm |
|
|
|
|
|
Page 1 of 1
|
[ 7 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 30 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
