|
|
It is currently Mon Nov 25, 2024 10:43 am
|
|
Page 1 of 1
|
[ 13 posts ] |
|
| Author |
Message |
|
Rox Crusher
Official CCB Member
Joined: Sun Oct 10, 2010 5:36 pm
Posts: 3980
Location: Roxborough Park, Colorado
|
 Hydraulic Press ? Does anybody know of or have a hydraulic press that is capable of pressing wheel studs into an axle flange ?
_________________
1977 Sport, 351w OBDII EFI motor, 4R70W auto, 4:88 gears, ARB lockers, 3.5" suspension, 33" tires.
|
| Sat Oct 18, 2014 2:28 pm |
|
|
|
Justin
Official CCB Member
Joined: Sun Oct 10, 2010 12:04 am
Posts: 6198
Images: 0
Location: Lakewood
|
Re: Hydraulic Press ? I've got one you're welcome to use.
|
| Sat Oct 18, 2014 3:06 pm |
|
|
|
Viperwolf1
Official CCB Member
Joined: Tue May 07, 2013 10:37 pm
Posts: 1485
|
Re: Hydraulic Press ? BFH
|
| Sat Oct 18, 2014 4:05 pm |
|
|
|
phyler
Official CCB Member
Joined: Sat Oct 02, 2010 9:41 pm
Posts: 1201
Location: Erie
|
Re: Hydraulic Press ? Funny, I have to do that tomorrow and was planning on the BFH method.
Sent from my HTC One using Tapatalk
_________________
1975 Ranger Edition that I've had longer than I've been without it.
|
| Sat Oct 18, 2014 4:34 pm |
|
|
|
Rox Crusher
Official CCB Member
Joined: Sun Oct 10, 2010 5:36 pm
Posts: 3980
Location: Roxborough Park, Colorado
|
Re: Hydraulic Press ? BFH didn't get it done.
Nor did a 20 ton hydraulic press.
I'm quite sure the holes in the axle flange are undersized for the wheel stud which I know to be the correct size.
_________________
1977 Sport, 351w OBDII EFI motor, 4R70W auto, 4:88 gears, ARB lockers, 3.5" suspension, 33" tires.
|
| Sat Oct 18, 2014 6:45 pm |
|
|
|
Justin
Official CCB Member
Joined: Sun Oct 10, 2010 12:04 am
Posts: 6198
Images: 0
Location: Lakewood
|
Re: Hydraulic Press ? You're not supposed to weld them in. 
|
| Sat Oct 18, 2014 7:53 pm |
|
|
|
ManTruck
Official CCB Member
Joined: Tue Oct 12, 2010 8:47 am
Posts: 200
|
Re: Hydraulic Press ? I'm sure you know this but I usually help my pressing by heating the axel or receiving part and freeze the pressed in piece prior to the instal. Seems to make a difference in what I break or don't break.
_________________
Owned my 1972 since 1985
Canon City, Co
|
| Sun Oct 19, 2014 5:47 am |
|
|
|
Colorado75bronc
Official CCB Member
Joined: Fri Oct 22, 2010 7:13 pm
Posts: 996
|
Hydraulic Press ? If you can't press in wheel studs than something has to be wrong, wrong studs, they should be able to be knocked out and in with a hammer
If you have an old one out, measure it with a vernier caliper or mic on the splined area, should be within a couple thousandths, the new should be just a little larger than the old .0005-.002" maybe 3 thousandths
_________________
75' bronco, 302, carb'd for now, i'm gathering parts for efi, 3g alternator, saginaw pump, 4x4x2 box, fw hp44, fw 9", N.P. 435 w/ gearbanger shifter, twin stick'd dana 20, 2" BL, 5.5" wildhorses lift, and 35" km2's
|
| Sun Oct 19, 2014 10:49 am |
|
|
|
Rox Crusher
Official CCB Member
Joined: Sun Oct 10, 2010 5:36 pm
Posts: 3980
Location: Roxborough Park, Colorado
|
Re: Hydraulic Press ? The studs came with the rear axle assembly for the kids Crown Vic Cop Car.
I'm thinking the holes are undersized, but I suppose it could be oversized wheel studs just as easily.
We are bringing the whole shebang back and exchanging them for another version of quality chinese parts.
_________________
1977 Sport, 351w OBDII EFI motor, 4R70W auto, 4:88 gears, ARB lockers, 3.5" suspension, 33" tires.
|
| Sun Oct 19, 2014 11:51 am |
|
|
|
Rox Crusher
Official CCB Member
Joined: Sun Oct 10, 2010 5:36 pm
Posts: 3980
Location: Roxborough Park, Colorado
|
Re: Hydraulic Press ? Orielly's rounded another up for us.
Holes were slightly larger than the ones in the the hacked up one, but still not big enough for the studs.
Nobody else has one so will probably go to the p-n-p next week end.
_________________
1977 Sport, 351w OBDII EFI motor, 4R70W auto, 4:88 gears, ARB lockers, 3.5" suspension, 33" tires.
|
| Sun Oct 19, 2014 5:24 pm |
|
|
|
Gregg
Official CCB Member
Joined: Sun Nov 07, 2010 11:08 am
Posts: 1060
|
Re: Hydraulic Press ? OOOOOOOOOOOOh! Now you want to go to the PnP.
You don't need special tools. You just have to be crafty. Remember my homemade press?
bubba tech2.jpg
You do not have the required permissions to view the files attached to this post.
_________________
Definition of cool.
|
| Mon Oct 20, 2014 11:11 am |
|
|
|
Dukietown
Official CCB Member
Joined: Wed Jun 08, 2011 12:24 pm
Posts: 523
Location: Denver
|
Re: Hydraulic Press ?
|
| Mon Oct 20, 2014 2:03 pm |
|
|
|
Eck
Official CCB Member
Joined: Thu Oct 25, 2012 9:33 pm
Posts: 2460
|
Re: Hydraulic Press ? Still waiting for that LIKE button!!
_________________
69 Wagon, 351W, Explorer EFI & Serpentine, ZF5, 35" tires, 3.5 SL, 2 BL, WARN 8274
|
| Mon Oct 20, 2014 3:19 pm |
|
|
|
|
|
Page 1 of 1
|
[ 13 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 42 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
