|
|
It is currently Sat Nov 23, 2024 11:09 am
|
|
Page 1 of 1
|
[ 5 posts ] |
|
Dana 44 ring gear engraving
| Author |
Message |
|
akaFrankCastle
Official CCB Member
Joined: Wed Oct 27, 2010 6:25 pm
Posts: 4901
Images: 0
Location: Colorado Springs
|
 Dana 44 ring gear engraving So, tonight I finally got around to opening a Dana 44 I picked up several months ago. The good news it is a 4.09 ratio with Trac-Loc.
While checking things out on the inside, I found an "A202" hand engraved into the outside of the ring gear. Anyone have any idea what that might mean? I'm thinking it was done by a PO. I'm just curious if it sounds like it would be pertinent to the set up or something.
_________________
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
|
| Sat May 09, 2015 8:24 pm |
|
|
|
Viperwolf1
Official CCB Member
Joined: Tue May 07, 2013 10:37 pm
Posts: 1485
|
Re: Dana 44 ring gear engraving It was probably done during manufacturing to identify the pinion gear matched to it.
|
| Sat May 09, 2015 9:09 pm |
|
|
|
akaFrankCastle
Official CCB Member
Joined: Wed Oct 27, 2010 6:25 pm
Posts: 4901
Images: 0
Location: Colorado Springs
|
Re: Dana 44 ring gear engraving I'll buy that.
_________________
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
|
| Sat May 09, 2015 9:28 pm |
|
|
|
BroncoCrawler
Official CCB Member
Joined: Sun Jul 14, 2013 9:21 am
Posts: 90
Location: Wheat Ridge, CO
|
Re: Dana 44 ring gear engraving Yep usually you will find the same phase engraved on the pinion to signify the pair. Also I use to see a +2 or -1 hand engraved on the end of the pinion. This was to show the approximate pinion depth during setup, unfortunately it seems gear manufacturers have stopped doing this.
|
| Sun May 10, 2015 9:14 am |
|
|
|
akaFrankCastle
Official CCB Member
Joined: Wed Oct 27, 2010 6:25 pm
Posts: 4901
Images: 0
Location: Colorado Springs
|
Re: Dana 44 ring gear engraving I have a feeling, based on the slop in this set up, that it's probably an OEM set up.
_________________
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
|
| Sun May 10, 2015 9:52 am |
|
|
|
|
|
Page 1 of 1
|
[ 5 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 3 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
